All Model Railroading Community Chat Forum  
AMR Shamus Cooncreek and Tumbleweed Springs AMR Shamus Badger Creek AMR Shamus How I make a model railroad

Go Back   All Model Railroading Community Chat Forum > Archive (Read Only) > Library > Weathering
Gallery Image Hosting Calendar FAQ Mark Forums Read

 
 
Thread Tools Display Modes
Old 23rd March 2006, 17:39   #1
Qube
Administrator
 
Qube's Avatar
 
Join Date: May 2004
Posts: 946
Default hminky's - Making Styrene Look Like Aging Wood






hminky's
- Making Styrene Look Like Aging Wood











(Click image
to enlarge)


This is an HO Atlas
Trackside Shanty. It is being built to represent an 1870's oil pump house.
It has been weathered with Kilz2 acrylic primer and a wash of black Liquid
Dye. Its construction will be covered in another piece.


The look of wood gradually
aging has been added using the following technique.


 


 






use a brass grill brush to give the styrene a dull texture





Simple roughing is best done with sandpaper.
Additional roughing can be applied with a hobby knife




Kilz2 acrylic primer is used to give the plastic "tooth" for the staining
with black Rit Liquid Dye. Drawing Ink in raw and burnt sienna will represent
the fresh wood, this is Koh-i-noor. Mark one brush with tape to be the black
brush.






 


























































 

The lustre
is taken off the styrene with either 220 grit sand paper or the
wire brush. There should be no original finish.





 

Add grain
to the plastic, this is 50 grit sandpaper. Additional knots and
checks can be added with a hobby knife.





 

Paint the
plastic with the Kilz2 primer. It will be slightly off white and
have a texture. Make sure to cover the entire piece.




Kits can be
primed after assembly and weathered.





 

Add a drop
of Rit Dye and water to the surface and scrub it around. Try to
make bubbles as they will add texture





 

If the plastic
is too light add more dye to the wet surface and swirl it around.





 

If the plastic
is too dark add more water and suck the excess up with a brush.





 

The plastic
when dry will look like weathered wood. The dye can be manoeuvred
around for other effects, but this is the plain vanilla effect.



Since the primer is stained by a small portion of the dye, the remaining
pigments can be redistributed for other effects.



This is the basic styrene to weathered wood technique.





 

To add the
effect of gradual aging raw sienna drawing ink is brushed along
the area representing the original wood. Mainly under the eaves
out of the sun and rain.





 

A tissue
is used to lightly smear the raw sienna ink downward. It will remove
the water soluble fabric dye. This gives a randomness to the procedure.





 

The light
area is the raw sienna. Add a little bit of burnt sienna. About
one eighth of that in the picture. Add a little water to the burnt
sienna and feather it about the raw sienna area.



The sienna moving it the black is colored with that dye and makes
a natural transition.





 

If you aren't
taking pictures and use less burnt sienna it will look better than
this picture. The burnt should add a subtle orange and not be so
distinct in its line. This dried too quickly while I was taking
pictures.









 

Add some
black dye and gently feather it into the sienna. The black may need
to be readjusted since it is water soluble it can be reworked again
and again. The ink is permanent.








The finished
look. It probably needs less burnt sienna unless you are representing
redwood.



This technique only
works on styrene. Wood is too porous. I have not tried other white primers
and black stains. I am sure that other combinations will get different results.





 


 







Original article by hminky -
http://www.pacificcoastairlinerr.com/aging_wood/

Qube is offline  
 

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Making styrene look like aging wood hminky Detailing and Weathering 8 23rd March 2006 22:29
Styrene looking like wood? hminky Detailing and Weathering 3 21st March 2006 07:03
George Carlin's Views on Aging -ENJOY!! Tileguy General Talk (Off Topic) 9 19th January 2006 00:14
Styrene as rough weathered wood hminky Scratchbuilding & Kitbashing 5 5th January 2006 05:47
Making plastic look like weathered wood hminky Detailing and Weathering 9 22nd December 2005 23:15


All times are GMT +1. The time now is 14:35.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2018, vBulletin Solutions, Inc.